Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 engine. Ideal worm motor applications where a simple to fit, high torque result is required. Great for student based projects which includes robots and buggies.
The unit has been designed to ensure that the output shaft could be ‘clicked’ in and out for modification. Electronic.g. cutting down to size. The electric motor is snap installed into its cradle to engage the apparatus and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + engine: 35(W) x 40(H) x 60(L)mm
The primary feature of this high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor isn’t turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for little walking robots, lifting mechanisms, and various other applications where high torque is usually desired.
The low-voltage motors in the worm gearbox operate on 1.5-4.5 volts and draft to some amps, making them ideal candidates for the DRV8833 motor driver carrier. Electric motor overheating can be due to excessive stalling, even at suprisingly low voltages. We recommend that you use stall-detection sensors, or just watch your robot, to ensure that it doesn’t stall for lots of seconds at a time.
This gearbox has a 4 mm diameter, round output shaft, which works with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also matches on the smaller threaded end of the shaft, though it is not particularly intended to work with this type of shaft (the hub’s set screw could damage the thread on the shaft).
Ever-Power equipment motors are economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical correct position worm geared motors established new criteria for reliability, effectiveness and economy with unparalleled features which includes hollow shafts in the smallest sizes. An inverter friendly style provides for easy integration today and a really future proof alternative. The Ever-Power gear electric motor offers total flexibility in mounting choices includes shaft, base, face, and flange solutions. The motor terminal box could be mounted in substitute positions rotated in 90º steps around the motor frame offering for unparalleled integration opportunities.
Ever-Power gear motors adhere to North American and International criteria, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a genuine total answer for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dirt tight and hose evidence,and can be used outside or in wet and dusty conditions without the utilization of additional enclosures. Full rated output is offered by the result shaft of the machine.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change 1st after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Regular), IP66 (Optional)
Additional features:
Connecting with Plug connectors.
With built-in inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category predicated on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the answer for applications requiring a corner turn, optional dual result, or an inability for the electric motor to be back again driven. The DC right angle equipment motors are made for continuous and intermittent duty procedure. Our right angle equipment reducers are designed with many mounting plate options, making them ideal for a variety of DC motor based applications. You can expect 12 ratios which range from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ hours (varies by application)
EP Products Worm Gear Motors are created to generate high torque in a little package size. Worm Gear Motors are great for applications that require a personal- locking or breaking feature since the result shaft can’t rotate when there’s no power used. Additionally, Worm Gearheads can transfer motion in 90 degrees. With various decrease ratios, precision cut gears, voltages and sizes, EP Products has a DC Worm Equipment Motor solution for your application.
Features and Benefits
Very High Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Capability to Handle Large Gear Decrease Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Security Door Locks / Industrial Conveying Systems / Security Gates / Teeth Chair / Ambulance Cots & Stretchers Many of our DC Motors could be complimented with among our Worm Gearheads. EP Products will continue to work with you to design and produce a Worm Gear Electric motor that may optimize the functionality of your specific application.
Built to your specific requirements
Engine Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Cut / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm motor runs on the metal gear box for toughness and a high torque output. Because of the special mechanical framework of the worm drive the motor output shaft can be self locking and may not be rotated.
This part runs on the two wire connection and supports direction control as well as PWM speed control. Ranked voltage is 12v and can attain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear devices from EP DRIVESYSTEMS especially display their power in applications where high equipment ratios are necessary. Our worm geared motors are consequently optimally suited for use in intralogistics, packaging technology and the food & beverage industry.
Four great known reasons for EP worm geared motors:
Rugged
Our worm geared motors have a higher overload capacity
Maintenance Friendly
Washdown versions enable simple and efficient cleaning of the drive program.
Corrosion protection
The NSD tupH sealed surface conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users maximum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are numerous applications that want drive systems, and each of these has its unique requirements. The EP series worm equipment motors can be quickly and efficiently adapted to satisfy your needs.
Worm gear models impress with their high power density and compact style. If required, we are able to also supply them with the highly effective nsd tupH surface treatment.
As well as the basic EP casing, you can expect an extensive type of bolt-on elements to customize the product including torque arms, shaft covers and output flanges. These could be very easily field set up, but we will also be happy to assemble the individual components for you.
Find out more about our modular SI worm geared motors!
Find out more
Simple and Clean: The EP worm gear unit SMI
SMI worm gear systems feature a clean, corrosion-resistant alluminum alloy casing. Optional nsd tupH surface area conversion makes the product ideally suited for severe and demanding industries like meals processing and pharmaceuticals.
Versatile input designs such as for example NEMA, IEC or immediate motor mounts in additional foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared electric motor program. The units possess on all sides different repairing possibilities and enable an easy assembling for the customer.
Various other drive configurationscan be created by use of built-on add-ons (e.g. torque arm and output flanges). The housings are made in light weight building out of aluminium die cast. Motor attachment is realised in general by way of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:result shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Purchase Worm Drive Gearbox with Engine – incorporating the next features: 1 to 6V voltage rating, 17100 rpm simply no load rate, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm wide, 40mm high, a robust worm drive gearbox powered by an MM28 electric motor (included), most ideal for applications where a simple to fit, high torque result is necessary, nylon housing and gear, requires light essential oil or silicon grease lubrication, well suited for student based tasks including robots and buggies.
Most ideal for applications where an easy to fit, high torque result is required
Perfect for student based projects including robots and buggies
Reversible High torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Features:
The electric motor is Gear DC motor with micro-turbine worm, you can transform the wiring-connection to improve motor rotation.
Turbo worm geared engine with self-lock, that’s, in the case of motor without electrical, the output axis can be fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole electric motor output shaft relatively-short than general gear motor, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Output torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windows, door, Mini winch. Ect.
In sumo robot or combat robot competition where high holding torque’s engine is essential in order to avoid your robot being pushed by your opponent robot. The worm gear is definitely a better option compared to the spur gear motor. How come worm gear so unique? Take a look wiki out: Worm Drive.
“Unlike with ordinary gear trains, the path of transmission (insight shaft vs output shaft) is not reversible when using large reduction ratios, because of the better friction involved between your worm and worm-wheel, when usually an individual start (a single spiral) worm can be used. This can be an advantage when it’s desired to eliminate any likelihood of the output driving the input.”
In other phrases, it is tough to push your load (example, your robot) if the motor isn’t power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g